英语翻译第八张Destination BusController SC:6 DestinationsController

英语翻译
第八张
Destination Bus
Controller SC:6 Destinations
Controller LC:32 Destinations
• Transitions are only performed on enabled destinations.
• Source selections only apply to enabled destinations.
Hold and press
Destination # to disable
selected destination
• Press Clear + All to
disable all enabled
destinations
Press to enable the desired destination.
Any combination can be selected —
buttons are not mutually exclusive.
Press to enable
all valid
destinations
Controller
LC only
第九张
Source Selection Bus
Controller SC:Sources 1 – 12 (direct),13 – 24 (shifted)
Controller LC:Sources 1 – 32 (direct),33 – 64 (shifted)
Top # (direct),bottom # (shifted)
Red LEDs
• Solid:Source is on Program,
associated destination is enabled
Blinking:Split is Off.Layer is on
Program,opposite Layer on Preview
Each source button is
an input that can be
assigned to a PIP,Key
or Aux destination.
Note:top and botton
rows change functions
in “Live Switch” modes
Press to access
all shifted sources
Source Buttons
Blinking:Source on Preview,
blinking layer active for modification
• Solid:Source on Preview,layer
not active for modification
第十张
Layer Control Section
Controller SC:
• Up to 6 layers,3 mixers
Controller LC:
• Up to 12 layers,6 mixers
Select any combination of
layers on Preview:
• Blinking:Layer is selected
and active for adjustment
• Solid:Layer is selected on
Preview,but is not active for
adjustment
Select unscaled
background A or B
on Preview
Within a mixer,select scaled
layer A or B on Preview,to
assign as PIP or Key
Red LEDs
Indicate layers
on Program
Select unscaled
DSK on Preview
• Changes mixer’s mode:Split mode (on),Mix mode (off)
• With layer button blinking,hold Split and press other layer to Join layers
• If Split blinks (after Preset recall),mixer changes mode after next trans
第十一张
Layer Functions Section
Access the Border
Menu.Double-punch
to turn border on or off
Copy layer to
opposite screen
(wide screen only)
Copy PIP
or Key
properties
Hold and press
User Key # to
store attributes
Change
active layer
to a PIP
Change
active layer
to a Key
Take active
layer to full
screen
Change layer
priority (Split
mode only)
Isolate a
layer for
adjustment
Access the
Frame
Grab Menu
Set up a “Move” on active
layer.Double-punch to
delete the Move setup
Remove
active layer
from Preview
Freeze the active
layer on Preview
and/or Program
Clear Layer + All
removes all layers
from Preview

第八张目的地总线控制器：6个目的地控制器：32个目的地•过渡只执行使目的地.•源选择只适用于使目的地.握压目的#禁用选择目的地•按清除+所有禁用所有启用目的地按使理想的目的地.可以任意组合选择—按钮并不是相互排斥的.按使所有有效的目的地控制器立法会的唯一第九张源选择总线控制器：1–12（直接）,13–24（转移）控制器：1–32（直接）,33–64（转移）顶#（直接）,底部#（转移）红色发光二极管•固体：源程序,相关的目标是使闪烁：分裂了.层论程序,对面层预览每个按钮是一个输入,可以分配到一个画中画,关键或辅助目标.注：上下行功能在“开关”模式新闻访问所有转移来源电源按钮闪烁：源于预览,闪烁层主动修改•固体：源预览,层不活跃的修改第十张控制部分控制器的资深大律师：•高达6层,3混频器控制器：•高达12层,6混频器选择任何组合层预览：•闪烁：选定层积极调整•固体层选择预览,但不活跃调整选择未经背景或乙预览在一个混频器,选择缩放层或预览,以如画中画或密钥分配红色发光二极管显示层程序上的选择未经磁盘上预览•变化的模式：分割模式（上）,混合模式（下）•层按钮闪烁,容纳分裂和其他层与层•如果分裂闪烁（后预设召回）,搅拌后变化模式下跨第十一张层功能部分访问边境菜单.double-punch打开或关闭边境复制层相反的屏幕（全屏幕）复制画中画或关键性能握压#到用户的关键存储属性改变活性层一个画中画改变活性层一个关键采取主动层全屏幕改变层优先（分裂模式）隔离层调整访问框架抓斗菜单成立了一个“移动”活动层.double-punch到删除移动删除活性层从预览冻结的活性层预览和/或程序透明层+所有删除所有层从预览